Automotive Tester PCE-CT 29
Views: 1000
$0.00
Description
Automotive Tester with a measuring range of 0 … 2000 µm / Micro-USB /
statistics function / limit value alarm function / temperature and moisture measurement / V-groove
Software for transferring the measured values / optionally with ISO calibration certificate
The automotive tester has a measuring range of 0 … 2000 µm. The Material tester can measure the coating thickness on ferrous (Fe) and non-ferrous (NFe) metals. For a better analysis of the measurements, the automotive tester has a measuring function based on the SSPC standards. With this function, the corrosion protection of a coating can be checked with the Material tester.
The Group function stores the measured values directly on the Material tester. A memory of 50 groups with 50 measurements each is available on the Material tester. In each group, statistics are created for all measured values from the Automotive Tester. All measurement data and statistics can be recalled after a measurement run on the Automotive Tester.
For further analysis of the measured values, the Material tester can be connected to a PC. The Automotive Tester has a micro-USB interface for this purpose. The software can be used to transfer the measurement data from the Material tester to a PC. In addition, it is possible to carry out live measurements with the Material tester using the software. For further processing of the measured values from the Automotive Tester, they can be exported in CSV and XLS format via the software.
In addition to the coating thickness measurement, the Automotive Tester can measure the temperature and humidity of the environment. Thus, the Automotive Tester can be used to find out whether the climatic conditions are right to carry out further processing on the coating.
With the V-groove, the coating thickness of, for example, pipes can also be determined with the Automotive Tester. Optionally, the Automotive Tester can be equipped with an ISO calibration certificate.
– Data memory for later evaluations
– Rechargeable batteries
– For ferrous and non-ferrous metals
– Alarm when limit value exceeded
– Statistics function for analyzing a test object
– Alignment sensor for turning the display
– Measuring range 0 … 1500 μm
– Graphic representation of the measured values
Specification
| Measurement on ferrous metal (Fe) | |
| Measuring range | 0 … 2000 µm |
| Resolution | 0.1 µm @ 0.0 … 99.9 µm |
| 1 µm @ 100 … 2000 µm | |
| Accuracy | ±(2 % ±2 µm of Mw.) |
| Repeatability | ±(1 % ±1 µm of Mw.) |
| Smallest radius of curvature | 1.5 mm |
| Smallest measuring area | Ø7 mm |
| Smallest layer thickness | 0.5 mm |
| Measurement on non-ferrous metal (NFe) | |
| Measuring range | 0 … 2000 µm |
| Resolution | 0.1 µm @ 0.0 … 99.9 µm |
| 1 µm @ 100 … 2000 µm | |
| Accuracy | ±(2 % ±2 µm of Mw.) |
| Repeatability | ±(1 % ±1 µm of Mw.) |
| Smallest radius of curvature | 3 mm |
| Smallest measuring area | Ø5 mm |
| Smallest layer thickness | 0.3 mm |
| Temperature | |
| Measuring range | 0 … 50 °C / 32 … 122 °F |
| Resolution | 0.1 °C / °F |
| Accuracy | ±1.2 °C / ±2.2°F |
| Humidity | |
| Measuring range | 0 … 100 % r. h. |
| Resolution | 0.1 % r. h. |
| Accuracy | ±3.2 % r. h. @ 20.0 … 70.0 % r. h. |
| ±4.0 % r. h. @ 0.0 … 19.9 % r. h. | |
| ±4.0 % r. h. @ 70.1 … 100.0 % r. h. | |
| Further specifications | |
| Base material for measurements Ferrous (Fe) and non-ferrous (NFe) metals | |
| Display | 2.4 ” LC display |
| Automatic display orientation | 0, 90, 180 and 270 °, can be switched off |
| (only measuring window) | |
| Statistic functions | average, highest, lowest and SDEV measured value |
| Measuring modes | direct, groups, SSPC |
| Units | µm, mm, mils, inch |
| Power supply | 2 x 1.5 V AA batteries |
| Interface | Micro-USB (for data transfer only) |
| Alarm | signal tone and / or LED signal light in case of |
| Exceeding of the adjustable upper and lower alarm limit | |
| Switch-off | Off, 30 seconds, 1 minute, 5 minutes |
| Menu languages | English, German, French, Spanish, |
| Italian, Portuguese, Chinese, Japanese | |
| Operating conditions | 0 … 50 °C, 20 … 90 % r.h., non-condensing |
| Storage conditions | -10 … +60 °C, 20 … 90 % r.h., non-condensing |
| Dimensions | 35 x 64 x 137 mm |
| Weight | 175 g |
Delivery Scope
1 x Automotive Tester PCE-CT 29
1 x set of standard foils
1 x carrying case,
1 x calibration plates (Fe and NFe)
1 x mass data storage
2 x 1.5 V AA battery,
1 x instruction manual
